In this guide
Here’s something that catches first-time painters off guard: fresh paint doesn’t cover wall flaws. It makes them easier to see. Hold a lamp at a low angle against a newly painted wall and every old ding, patch, and crack stands out against the new color. That’s not a painting problem. That’s a prep problem.
The Painting and Decorating Contractors of America puts surface preparation at 80% of what determines paint quality and how long the job lasts. The paint itself is almost beside the point. Get the wall wrong and the best paint in the store won’t save it.
Gloss Makes Flaws Visible—Flat Hides Them
A coat of interior paint is about as thick as a human hair—4 to 6 mils. It doesn’t fill anything. It sits on whatever surface is under it, following every ridge, depression, and patch boundary exactly.
Flat paint scatters light in all directions, which is forgiving on an imperfect surface. Satin and semi-gloss reflect light directly, so bumps and patches cast tiny shadows that weren’t visible before. Sherwin-Williams’ finish guide is explicit about this: glossier finishes demand cleaner, more even surfaces. A kitchen wall with unrepaired dings painted in semi-gloss will show all of them. In flat, most would disappear—but flat doesn’t wipe clean, which is why nobody uses it in kitchens.
So the glossier the chosen paint, the more work the prep needs to do. Bathroom and kitchen walls demand more attention than bedroom walls—not because the damage is worse, but because the sheen will reveal more of it.
Washing the Wall Is Not Optional
Paint won’t stick to grease, smoke residue, or soap film. It bonds to those surfaces for a while, then lifts in patches. A kitchen wall that looks clean may still have a thin layer of cooking grease on it that water alone won’t cut through.
Trisodium phosphate—TSP—handles grease and residue that a damp cloth misses. EPA guidance on TSP cleaning suggests one tablespoon per gallon of warm water, applied and then rinsed clean. After rinsing, the wall needs at least 24 hours to dry before anything else goes on it.
Mold is different—washing it isn’t enough. A mix of one part household bleach to three parts water, left on the surface for 10 minutes, then scrubbed and rinsed, kills what’s there. Painting over mold without treating it first just delays the problem. The mold grows back through the new paint within weeks.
Filling: Different Problems Take Different Products
Small Holes From Nails and Screws
Lightweight spackle—the pink kind that turns white as it dries—works for holes under about a quarter inch. Push it in slightly past flush with a putty knife. When it’s completely dry, sand it flat with 120-grit paper, then feather the edges with 220-grit. Run a fingertip over it. If there’s any ridge or depression, that exact spot will show through paint.
Applying spackle level with the surface is the mistake most people make. It shrinks when it dries and leaves a slight hollow. A small overfill, sanded back to flat, is the way to get a result that actually disappears.
Bigger Holes From Anchors or Impact Damage
Once a hole gets past a quarter inch, spackle isn’t the right product. Setting compound hardens through a chemical reaction rather than by drying out—which means it doesn’t shrink. The Drywall Finishing Council recommends two thin applications for anything over half an inch. The first fills the void. The second spreads outward past the edges of the repair, blending it into the surrounding wall. A patch with sharp edges always looks like a patch.
Cracks Along Corners and Ceiling Lines
These cracks come from the building settling—temperature and humidity shifts cause slight movement all year. Spackle cracks along with the wall because it’s rigid. The right product is a flexible paintable caulk: it moves when the wall moves, so the repair stays closed. Apply it with a finger, smooth it flush, let it cure.
Cracks wider than 1/8 inch, or any crack running at a diagonal, may point to something structural rather than cosmetic. The International Association of Certified Home Inspectors flags diagonal cracks and anything over 1/4 inch wide as worth investigating before patching over them.
For cracks up to 3/8 inch, fiberglass mesh tape over the crack followed by two or three thin coats of joint compound is the fix. The tape keeps the crack from reopening through the compound. Sand each coat lightly before applying the next.
Sanding Isn’t Just for Repairs
The repaired spots need sanding. So does the rest of the wall. New paint needs something to grip—a glossy existing surface doesn’t give it much. A pass with 150-grit on a sanding block gives the surface enough tooth without cutting visible scratches into it. PDCA preparation standards are clear that a previously painted wall in decent condition only needs a light scuff, not heavy sanding.
Once the sanding is done, wipe everything down with a tack cloth or a barely damp rag. The dust that sanding leaves behind gets sealed under the primer and creates a gritty texture in the final coat. Getting it off is the last thing to do before priming.
Prime the Spots That Need It—Skip the Rest
Primer isn’t always necessary on a repaint. A wall in reasonable shape being repainted in a similar color doesn’t need it. But there are four situations where it’s not optional: new drywall, repaired patches, existing stains, and big color changes. Benjamin Moore’s primer guidance covers each of these specifically.
Each filled spot needs spot-priming before the finish coat goes on. Raw spackle and compound absorb paint faster than the surrounding painted wall, which leaves a flat, dull spot—called flashing—that shows through multiple finish coats. A quick hit of primer on each repair stops this from happening.
Stains from water, smoke, or grease need shellac-based primer—regular water-based primer won’t block them. Zinsser BIN shellac primer is what most painters reach for when a stain has to be sealed completely. Apply it to the stained area, let it dry, then paint over it normally.
The Lamp Test Before the First Coat
Take a work light or a strong flashlight and hold it close to the wall, nearly parallel to the surface. Any imperfection—a missed patch, a sanding scratch, an uneven area—will cast a shadow and become obvious. This takes about two minutes and catches problems while they’re still easy to fix.
PDCA lists this technique as the standard check between preparation stages. Run it after sanding, then again after priming. A flaw caught before the finish coat is a 10-minute fix. The same flaw found after the final coat is a reason to repaint.
Repair Reference
| Problem | Right Fix | Common Mistake |
| Nail hole (small) | Lightweight spackle; sand flush when dry | Skipping sanding—leaves a raised ring |
| Anchor hole (larger) | Setting compound; two thin coats | One thick coat—cracks as it dries |
| Hairline crack | Flexible paintable caulk; smooth with finger | Spackle—rigid, crack returns next season |
| Wide crack (>1/8 inch) | Setting compound + mesh tape | Caulk—not strong enough here |
| Scuff or ding (no hole) | Sand, prime, paint | Skipping prime—repair flashes through |
| Grease or smoke stain | TSP clean; shellac primer | Painting over—stain bleeds through |
| Old texture bump | Sand down; prime the sanded area | Painting over—sheen makes it worse |
Bottom Line
Clean the wall, fill the damage, sand everything flat, prime what needs it, then paint. Each step has to be finished before the next begins. Cut the cleaning and the paint won’t stick. Skip the repairs and every flaw telegraphs through the new color. Bypass the sanding and the finish coat slides off. Miss the spot-priming and every patch flashes. There’s no shortcut that doesn’t show up later on the wall.
Sources
Every external claim in this guide links to its origin. Collected automatically from the text above.
- The Painting and Decorating Contractors of America — pcapainted.org
- Sherwin-Williams' finish guide — sherwin-williams.com
- EPA guidance on TSP cleaning — epa.gov
- The Drywall Finishing Council — awci.org
- The International Association of Certified Home Inspectors — nachi.org
- Benjamin Moore's primer guidance — benjaminmoore.com
- Zinsser BIN shellac primer — rustoleum.com
